DEFECT ANALYSIS OF RUBBER PRODUCTS USING FISHBONE AND PARETO CHART METHODS AT CV ANM TECH
Abstract
This research aims to identify the main causes of rubber product defects at CV ANM TECH using the Fishbone Diagram and Pareto Chart methods. The primary issue faced is a high level of product defects, especially due to burning, which impacts quality reduction, customer dissatisfaction, and significant financial losses. Analysis results indicate that product defects are largely caused by poor raw material quality, suboptimal machine settings, inadequate technical training for workers, unmaintained work environment cleanliness, and an ineffective production monitoring system, leading to late detection of new problems. Over 70% of defects are attributed to non-conforming raw materials and operational errors. The study recommends improving raw material management, standardizing work procedures through SOPs, implementing technical training programs for workers, and strengthening quality control to reduce defect rates, enhance efficiency, and bolster the company's competitiveness.
Keywords: Rubber products, defects, Fishbone Diagram, Pareto Chart, quality control, CV ANM TECH
Full Text:
PDFReferences
Alam, W. P. (2018). Perencenaan Persediaan Bahan Baku Wajan dengan Metode MRP (Material Requirement Planning) pada Perusahaan Cor Alumunium Bintang Dua di Kec. Cikoneng Kab. Ciamis. Jurnal Media Teknologi, 5(1), 41–62.
Hidayat, R., & Wijaya, A. (2023). Implementasi Metode Pareto Chart dan Ishikawa Diagram untuk Menurunkan Defect Terbakar pada Proses Vulkanisasi Karet. Jurnal Serambi Engineering, 8(3), 6120-6129.
Hapari, M. M. M. (n.d.). Upaya UPT Pelatihan Kerja Jombang dalam Peningkatan Kualitas Tenaga Kerja Melalui Standarisasi Kegiatan Pelatihan. FISH UNESA, 1–17.
Hulu, Y. M. S. M. K. E. (2022). Pengaruh Kualitas Produk Terhadap Kepuasan Pelanggan Pada PT. INDOMARCO ADI PRIMA CABANG MEDAN STOK POINT Nias Kota Gunungsitoli. Jurnal Ilmiah Simantek, 6(4), 106–115.
Kustoyo, H. C. P. T. D. (2024). Upaya Penurunan Kecacatan Produk Proses Blow Molding pada Industri Kemasan PT. X. Tirta, 12(2), 25–32.
Prabhakar, V., & Khan, A. A. (2021). Optimization of process parameters to minimize flash and underfill defects in rubber injection molding. International Journal of Production Research, 59(14), 4210-4226.
Pratama, M. A., & Supriyadi, S. (2024). Peningkatan Kualitas Produk Komponen Otomotif Berbahan Dasar Karet Melalui Pendekatan DMAIC dan Diagram Sebab-Akibat. Jurnal Media Teknik dan Sistem Industri, 8(1), 12-23.
Ramadhan, F., & Purba, H. H. (2021). Analisis Kerusakan Produk Rubber Gasket dengan Menggunakan Pendekatan Seven Tools untuk Pengendalian Kualitas. Jurnal Rekayasa Sistem Industri, 10(1), 35-44.
Rinjani, W. W. B. N. I. (2021). Analisis Pengendalian Kualitas Produk Cacat pada Lensa Tipe X Menggunakan Lean Six Sigma dengan Konsep DMAIC. Jurnal Pendidikan dan Aplikasi Industri (UNISTEK), 8(1), 18–29.
Riyanto, O. A. W. (2015). Implementasi Metode Quality Control Circle untuk Menurunkan Tingkat Cacat pda Produk Alloy Wheel. JEMIS, 3(2), 104–110.
Santos, J., & Silva, G. (2024). The impact of raw material variability on defect rates in rubber manufacturing: An industrial assessment. Journal of Manufacturing Processes, 102, 315-328.
Sari, D. P., & Utami, S. (2023). Analisis Cacat Produk Cetakan Kurang Isi (Underfilled Molding) pada Industri Karet menggunakan FMEA dan Fishbone. Jurnal Optimasi Sistem Industri, 16(2), 89-98.
Sayuti, B. S. M. (2017). Pengaruh Lingkungan Kerja Terhadap Kualitas Produk IKM Kerupuk Udang di Kabupaten Indramayu. IndustryXplore, 2(1), 35–46.
Shiyamy, S. R. A. S. A. F. (2021). Analisis Pengendalian Kualitas Produk dengan Statistical Process Control. Jurnal Ilmiah Manajemen, 2(2), 32–45.
Suharyanto, R. L. H. A. M. (2022). Analisis Pengendalian Kualitas Produk Waring dengan Metode Seven Tools di CV. KAS SUMEDANG. TEDC, 16(1), 37–47.Aguilar, F. J. (1967). Scanning the business environment. Macmillan.
Zheng, X., & Takahashi, M. (2023). Standard Operating Procedures (SOP) and human error mitigation in rubber components assembly lines. International Journal of Industrial Ergonomics, 95, 103-115.
DOI: https://doi.org/10.71312/mrscholar.v2i2.552
Multidisciplinary Research Studies in Social Sciences (MRSCHOLAR) Indexed by:
Publisher: Taksasila Edukasi Insani
Contact: Tri Ananto
Publisher Address: Jl. Cireundeu Raya No.1A, RT.002/RW.06, Kelurahan Cireundeu, Kecamatan Ciputat Timur, Kota Tangerang Selatan, Banten 15419.
Copyright © 2025 of Multidisciplinary Research Studies in Social Sciences (e-ISSN: 3090-8922 )
Multidisciplinary Research Studies in Social Sciences © 2025 by Taksasila Edukasi Insani is licensed under Creative Commons Attribution-ShareAlike 4.0 International .